BACK NEXT

2.4.1. Writing "Hello World" to LCD Character in the Upper Left firs Line.

In this lesson, you can try to write word " Hello World " in first line of LCD Character.

Step 1st
Build the circuit as shown in figure 2.11. As you seen on figure 2.11. P0.0 trough P0.7 is connected to DB0 - DB7,and P2.0- P2.1. is connected to RS and EN each. Remember, that all we want to do with this lesson is write " Hello World ", in the first line of LCD Character

Step 2nd
In this step, you must tipe the assembly program to make your LCD Character shown the word, we assume that you have already known the editor, we used MIDE-51 to edit the program. ( Download File asm : exp241.zip , Download Complete Circuit File : LCDCharacter.PDF )

       org 0h
start: call init_LCD
       mov R1,#80h
       call write_inst
       mov R1,#'H'
       call write_data
       mov R1,#'e'
       call write_data
       mov R1,#'l'
       call write_data
       mov R1,#'l'
       call write_data
       mov R1,#'o'
       call write_data
       mov R1,#' '
       call write_data
       mov R1,#'W'
       call write_data
       mov R1,#'o'
       call write_data
       mov R1,#'r'
       call write_data
       mov R1,#'l'
       call write_data
       mov R1,#'d'
       call write_data
EndChar:
       sjmp Endchar

Init_lcd:
    mov r1,#00000001b ;Display clear
    acall write_inst  ;
    mov r1,#00111000b ;Function set,
                      ;Data 8 bit,2 line font 5x7
    acall write_inst  ;
    mov r1,#00001100b ;Display on, 
                      ;cursor off,cursor blink off
    acall write_inst
    mov r1,#00000110b ;Entry mode, Set increment
    acall write_inst
    ret
;
Write_inst:
    clr P2.0  ; RS = P2.0 = 0, write mode instruction
    mov P0,R1 ; D7 s/d D0 = P0 = R1
    setb P2.1 ; EN = 1 = P2.1 
    call delay; call delay time
    clr P2.1  ; EN = 0 = P2.1
    ret
;
Write_data:
    setb P2.0 ; RS = P2.0 = 1, write mode data
    mov P0,R1 ; D7 s/d D0 = P0 = R1
    setb P2.1 ; EN = 1 = P2.1
    call delay; call delay time
    clr p2.1  ; EN = 0 = P2.1
    ret
;
delay: mov R0,#0
delay1:mov R7,#0fh
       djnz R7,$
       djnz R0,delay1
       ret
;
end

Step 3rd
Safe your assembly program above, and name it with lcd1.asm (for example) Compile the program that you have been save by using MIDE-51, see the software instruction.

Step 4th
Download your hex file ( lcd1.hex ) into the microcontroller by using Microcontroller ATMEL ISP software, see the instruction.After download this hex file you'll see the action of the 7 segmen( of course if your cable connection and your program are corrected ).

BACK NEXT

Lesson 1:
T o o l
1.1. Programmer
1.2. Edsim 51
1.3. MIDE-51
1.4. ATMEL ISP

Lesson 2:
Input Output
2.1.LED
2.2.Swicht
2.3.7 Segmen
2.4.LCD Character
2.5.ADC
2.6.DAC
2.7.Motor Stepper
2.8.Keypad

Lesson 3:
Timer Counter
3.1.Basic
3.2.Mode 0
3.3.Mode 1
3.4.Mode 2
3.5.Mode 3

Lesson 4:
Serial Comm.
4.1.Basic
4.2.LED
4.3.Rotate LED
4.2 ADC
4.3.LCD

Lesson 5:
Interuption
5.1.Basic
5.2.Timer
5.2.External